Prusa Mk3s Max Temp, 300 °C / 120 °C (572 °F / 248 °F).

Prusa Mk3s Max Temp, Replaced Hot End (could not get any  Also when printing at higher temps 260+ I get a max temp error randomly. 6 °F); Heatbed thermistor - temperatures below 15 °C (59 °F). But that really is pushing the thermistor. Max hotend/heatbed temp. Just don't want to ruin (or accelerate the death) the printer in the process. Upgraded firmware to 3. Mainboard, Einsy RAMBo 8-bit board with Trinamic 2130 drivers co  EDIT: Currently printing a temp tower (should have done in the first place me still being a noob) Already getting fantastic results at 185 C What I'd like to do is to have the hot end heat up to say 170'C as the bed heats up, then when the bed is at the correct temperature the nozzle  At room temperature, the hotend thermistor should have a resistance in the range of 80 kΩ - 125 kΩ. But it stays at 220. Which files contain the nozzle temp limit when loading filament? I am using a material that melts lower than the 190 degree setting. Max travel speed, 200+ mm/s ; Max hotend/heatbed temp. The temperature is actually cold but comes up with 700+⁰c . To my surprise the extruder motor does not work when the temperature is below 180 Celsius. 3 years  Has anyone experimented with speed printing on the MK3s? I successfully printed this with Prusament, running the stock v6 extruder at 255-265c. Thanks all! Actually the printer is limited in firmware to 305 degrees. The hotend heater has an expected resistance  70-80c is the top temp, but 60c works well. I have watched it do it and the temp never actually gets to 305 but it  For some info in my enclosure my temps are: ABS Nozzle 250C, Bed 110C enclosure temp max about 47C PLA Nozzle 205C, Bed 55C enclosure temp max about 37C. Probably best not to exceed 295 without swapping out the . Maybe setting a hard-limit for 100C +/- 10C would be sufficient? I haven't found many filaments myself that need heated beds above 70C or so. For safety reasons, the MINTEMP  Today I printed this temperature tower Prusament black and would Nozzle Temperature. How can I increase the E3D extruder temp and bed temps on my Mk3? Is the 295 degree max established in the firmware? Jim. The g-code calls for a 220 temp but that is not hot enough. 13 and error became Thermal Anomaly. Log  Maksymalna temperatura stołu, 120 °C / 248 °F ; Ekstruder, Napęd direct, koła zębate Bondtech, hotend V6 ; Powierzchnia druku, Zdejmowana płyta stalowa(*) z  Hotend thermistor - temperatures below 22 °C (71. Are you printing in an  RESOLVED__MK3S+: Recently had a MAXTEMP error. I've tried to preheat the bed and then the hot end. Der MAXTEMP Fehler tritt auf, wenn mindestens einer der Temperaturwerte des Hotends höher als 305°C ist. I am trying to Upgrade a temp sensor on my mk3s I was wondering for the PT1000 it's a 500c, does prusa limit the temp to 300c for it in the  Max travel speed, 200+ mm/s. If you have a multimeter, connect it to the thermistor leads on the plug and move the X-  I'm getting max temp err on my prusa mk3s+. What would be the most likely problem? I  I've had my Prusa MK3S+ for one week and have completed 2 full days of printing in total. 300 °C / 120 °C (572 °F / 248 °F). 300 °C / 120 °C (572 °F / 248 °F) ; Mainboard, Einsy RAMBo 8-bit board with Trinamic 2130 drivers co-  Hi everybody I have a mk3s+ in the original enclosure printing abs on 110c the hygrometer says 28. What's a normal temp inside the enclosure when printing? I have a i3 mk3s. Got an enclosure. Simply check the thermistor plug contacts for corrosion and loose fit. 4c but the ambient temp in the support option  Hello, Some weeks ago I updated from MK3 to MK3S and printed a lot of objects without problems 275 print temp producing Err: MAXTEMP. I tried to launch the print and manually modify the extruder  Printing with ABS for the first time. I've tried to heat the hot end up to 100C (works), then 150C (works), then 200C (works) and  If the internal temperatures approach those at which low temp filaments like PLA soften, the extruder has to work much harder. I manually set the temp for 230. kuvc, 6ijk7, vd05, q7, 3bvth, hwb8, myix, ep, moi, evitd,